Repairs

Adjusting the boot lid

Adjust the boot lid height and alignment, including panel gaps and the striker.

Adjust the boot lid height and alignment, including panel gaps and the striker.

Searchable source text / notes
Page 1
AR88.50-P-5200EW       Adjust trunk lid                                                                  28.10.15

Model     212.0/1, 218.3

Modification notes

16.9.15       Information on calibration revised.                        Operation step 15, 16

Shown on model 212.0/1

1  Cover
2   Bolts
3   Locking striker
4   Hinge lever trim pieces
5  Cover
6   Bolts
7   Trunk lid
8   Stops

                                                                                                                                                          P88.50-2943-06

   DangerDanger !!           Risk of injury caused by fingers being      No parts of the body or limbs should be within AS00.00-Z-0011-01A
                    jammed or pinched when removing, installing  the operating area when the components are
                           or aligning hoods, doors, trunk lid/rear-end    moving.
                        door or sliding roof.
                       Notes on sensor system for trunk lid opening/                                         AH80.61-P-0001-01A
                           closing
                  Remove

1                  Remove cover (1)
2                    Unscrew bolts (2) and remove locking striker
                             (3)
3.1                 Remove left and right hinge bracket trim piece Model 212.0/1
                             (4)
3.2                   Loosen left and right hinge bracket trim piece Model 218.3
                             (4) from trunk lid (7)
                       Adjust
4                                 Lift paneling (5) at side on left and right hinge   If trunk lid (7) is to be adjusted longitudinally.
                           lever and loosen bolts (6)
5                        Adjust trunk lid (7) in longitudinal direction        If trunk lid (7) is to be adjusted longitudinally.
                                                            Model 212.0/1                          AR60.00-P-0700-01EW
                                                            Model 218.3                             AR60.00-P-0700-01EL
                                                            Model 212.0/1Gap dimension               *BE60.00-P-1003-01U
                                                            Model 218.3Gap dimension                *BE60.00-P-1003-01O
                                                                         Feeler gauge                        *129589032100
6                       Tighten bolts (6) on left and right hinge lever    If trunk lid (7) was adjusted longitudinally.
                                                                                    Nut/bolt, hinge lever to trunk lid          *BA88.50-P-1002-01E
7                    Screw in stops (8)                   When height of trunk lid (7) is adjusted.
8                      Center lock striker (3) in relation to trunk lid   When height of trunk lid (7) is adjusted.
                           lock and adjust so that the height of the trunk
                                   lid (7) coincides with the height of the rear
                         fenders
9                       Tighten bolts (2) for locking eye (3)        When height of trunk lid (7) is adjusted.
10                    Coat contact surface on end stops (8) with   When height of trunk lid (7) is adjusted.
                         chalk
© Mercedes-Benz AG, 7/20/22, X/07/22, ar88.50-p-5200ew, Adjust trunk lid                                                                                  Page 1 of 3
Model 212.0/1, 218.3

Page 2
11                 Remove end stops (8) until the chalk on the  When height of trunk lid (7) is adjusted.
                          contact surfaces of the rear center section and
                          the two rear fenders is visible when the trunk
                                   lid (7) is closed
                                                      Do not slam trunk lid (7), instead, push
                                                                        slowly into lock by hand.
                             Install
12                      Repair paint damage on bolts (6) with touch-    If trunk lid (7) was adjusted longitudinally.
                     up paint pen
13.1                          Install left and right hinge lever trim piece (4)  Model 212.0/1
13.2                   Fasten left and right hinge bracket trim piece  Model 218.3
                             (4) on trunk lid (7)
14                            Install cover (1)
                         Calibrate
15                        Calibrate reversing camera using diagnostic  Model 212.0/1
                      system and calibration device              up to model year 2014
                                                                          with code 218 (Rear view camera)
                                                            Model 212.0/1                          AR54.65-P-0022GZ
                                                           up to model year 2014
                                                                          with code 218 (Rear view camera)
                                                                          with code 498 (Japanese version)
                                                            Model 218.3
                                                           up to model year 2013
                                                                          with code 218 (Rear view camera)
                                                                          with code 498 (Japanese version)
                                                                                Calibration device                    *000589012100
16                        Calibrate rear 360° camera using the        Model 212.0/1
                          diagnostic system                              with code 501 (360° camera)
                                                                                                     AD00.00-P-2000-04A

Test values for gap dimensions on hoods, doors and lids

Number              Designation                                                  Model 218.3
BE60.00-P-1003-01O  Gap dimension         Trunk lid to rear     Dimension "J"    mm    4,0 (  1)
                                                   fender, top
                                             Trunk lid to rear lamp Dimension "K"    mm    5,0 (  1)
                                                        unit
                                             Trunk lid to bumper  Dimension "L"    mm    5,5 (  1)
                                          Rear fender to lamp  Dimension "M"    mm    3,0 (  1)
                                                        unit
                                                                        Picture                    AR60.00-P-0700-01
                                                                           EL

Check values for gap dimensions

Number              Designation                                                  Model 212.0/1
BE60.00-P-1003-01U  Gap dimension         Trunk lid to rear     Dimension "L"    mm   4 (  1)
                                                   fender, top
                                             Trunk lid to taillamp  Dimension "M"    mm   –
                                             Trunk lid to bumper  Dimension "N"    mm    6,5 (  1)
                                          Rear fender to      Dimension "O"    mm   2 (+1,5/-1)
                                                    taillamp
                                                Taillamp to bumper  Dimension "P"    mm   2 (  1)
                                             Trunk lid taillamp to  Dimension "M1"   mm   4 (  1,5)
                                                    taillamp
                                                                        Picture                    AR60.00-P-0700-01
                                                         EW

    Trunk lid

Number              Designation                                                  Model 212        Model 218.3
BA88.50-P-1002-01E    Nut/bolt, hinge lever to trunk lid                      Nm   6                 10

© Mercedes-Benz AG, 7/20/22, X/07/22, ar88.50-p-5200ew, Adjust trunk lid                                                                                  Page 2 of 3
Model 212.0/1, 218.3

Page 3
        129 589 03 21 00                000 589 01 21 00

                Feeler gauge                                  Calibration device

© Mercedes-Benz AG, 7/20/22, X/07/22, ar88.50-p-5200ew, Adjust trunk lid                                                                                  Page 3 of 3
Model 212.0/1, 218.3