Repairs

Removing the front bumper

Step-by-step W212 front bumper removal. Confirm model year and equipment before starting.

Step-by-step W212 front bumper removal. Confirm model year and equipment before starting.

Searchable source text / notes
Page 1
AR88.20-P-2000EW       Remove/install front bumper                                                       26.2.10
MODEL    207, 212

Shown on model 212 on right side vehicle

1   Bumper
2    Front fender
3    Quick-release coupling
4     Air ducting
5   Screw
6     Electrical connector
7   Screw
8    Bracket
9    Bolts

                                                                                                                                                         P88.20-3340-06

E1/3     Left daytime running lamps headlamp                          X26/38    Front bumper and frame wiring harness electrical
E2/3    Right daytime running lamps headlamp                                     connector

                        Remove/install

   Danger!            Risk of death caused by vehicle slipping or  Align vehicle between columns of vehicle lift  AS00.00-Z-0010-01A
                           toppling off of the lifting platform.           and position four support plates at vehicle lift
                                                                    support points specified by vehicle
                                                                    manufacturer.
1                                  Lift vehicle on lifting platform.
2.1                 Remove radiator grille                    Model 212                            AR88.40-P-4001EW
2.2                   Loosen radiator grille at top of radiator       Model 207                             AR88.40-P-4001EC
                         support

                                                   On model 207 the radiator grille remains
                                                           on the bumper (1).
3                         Pivot left and right air ducting (4) to side and
                      unscrew bolt (5)
4                  Remove quick-release coupling (3)
5                  Remove left and right fender liner front                                            *110589035900
                          section
6                    Unscrew bolts (9) on left and right front
                         fender (2)
7                       Disconnect electrical connector on frame
                            wiring harness and front bumper (X26/38)
8                       Disconnect electrical connector (6) from        Depending on vehicle configuration.
                        daytime running light (E1/3) and right
                        daytime running light (E2/3), expose
                              electrical wiring harness
9                       Disconnect electrical connector from left and    Depending on vehicle configuration.
                               right front fog lamp, expose electrical wiring
                        harness
10                   Unscrew bolt (7) form left and right bracket
                              (8)
11                    Guide bumper (1) out left and right bracket        Installation: Install engine compartment
                              (8)                                         paneling below bottom section of
                                                                   soundproofing on bumper (1).
12                     Press bumper (1) toward front and remove        Installation: Screw in bolts (5, 7, 9) only
                                                                             to stop because it may be necessary to
                                                              check and adjust the gap dimensions after
                                                         bumper (1) installation.
                                                            Model 207                             AR60.00-P-0700-01EC
                                                    Gap dimension "C, E"                    *BE60.00-P-1001-01W
                                                                                                  *129589032100

Page 2
                                                    Gap dimension "D, F"                     *BE60.00-P-1001-01U
                                                                                                  *129589032100

13                    Disassemble front bumper (1)                 Only when replacing bumper (1).        AR88.20-P-2050EW
14                             Install in the reverse order
15                   Check adjustment of left front fog lamp and   Model 207, 212                        AP82.10-P-8260EW
                               right front fog lamp, adjust if necessary       without code (615) Bi-xenon headlamp unit
                                                                          with integrated curve illumination
                                                                        without code (616) Bi-xenon headlamp unit
                                                                          with integrated asymmetric curve illumination
                                                                        without code (621) Intelligent Light System
                                                                             (left-hand traffic system),
                                                                        without code (622) Intelligent Light System
                                                                          (right-hand traffic system)

Check values for gaps

 Number               Designation                                                   Model 207.3

 BE60.00-P-1001-01W       Gap       Engine hood to fender                    Dim. "A"   mm  4 ( 1)
                        dimension

                                   Engine hood to headlamp                 Dim. "B"   mm  4 ( 1)

                                   Engine hood to bumper                   Dim. "C"   mm  6 (+1/-2)

                                   Engine hood to A-pillar                   Dim. "D"   mm   4.5 (+2/-1)

                               Bumper to headlamp                     Dim. "E"   mm   2.5 ( 1.5)

                                                                See picture
                                                                                                                       AR60.00-P-0700-01E

                                                                                        C

Check values for gaps

 Number               Designation                                                   Model 212.0/1    Model 212.2

 BE60.00-P-1001-01U       Gap       Engine hood to fender                    Dim. "A"   mm  4 ( 1)           4 ( 1)
                        dimension

                                   Engine hood to headlamp                 Dim. "B"   mm  4 ( 1)           4 ( 1)

                                   Engine hood to radiator grille              Dim. "C"   mm    -                         -

                                   Engine hood to bumper                   Dim. "D"   mm   4.5 ( 1.5)          4.5 ( 1.5)

                                   Engine hood to A-pillar                   Dim. "E"   mm   4.5 ( 1.5)          4.5 ( 1.5)

                               Bumper to headlamp                     Dim. "F"   mm   3.5 ( 1.5)          3.5 ( 1.5)

                                                                See picture
                                                                                                                       AR60.00-P-0700-01E    AR60.00-P-0700-01E

                                                                    W           W

       110 589 03 59 00                129 589 03 21 00

             Mounting wedge                                Feeler gauge