Step-by-step W212 front bumper removal. Confirm model year and equipment before starting.
Searchable source text / notes
Page 1
AR88.20-P-2000EW Remove/install front bumper 26.2.10
MODEL 207, 212
Shown on model 212 on right side vehicle
1 Bumper
2 Front fender
3 Quick-release coupling
4 Air ducting
5 Screw
6 Electrical connector
7 Screw
8 Bracket
9 Bolts
P88.20-3340-06
E1/3 Left daytime running lamps headlamp X26/38 Front bumper and frame wiring harness electrical
E2/3 Right daytime running lamps headlamp connector
Remove/install
Danger! Risk of death caused by vehicle slipping or Align vehicle between columns of vehicle lift AS00.00-Z-0010-01A
toppling off of the lifting platform. and position four support plates at vehicle lift
support points specified by vehicle
manufacturer.
1 Lift vehicle on lifting platform.
2.1 Remove radiator grille Model 212 AR88.40-P-4001EW
2.2 Loosen radiator grille at top of radiator Model 207 AR88.40-P-4001EC
support
On model 207 the radiator grille remains
on the bumper (1).
3 Pivot left and right air ducting (4) to side and
unscrew bolt (5)
4 Remove quick-release coupling (3)
5 Remove left and right fender liner front *110589035900
section
6 Unscrew bolts (9) on left and right front
fender (2)
7 Disconnect electrical connector on frame
wiring harness and front bumper (X26/38)
8 Disconnect electrical connector (6) from Depending on vehicle configuration.
daytime running light (E1/3) and right
daytime running light (E2/3), expose
electrical wiring harness
9 Disconnect electrical connector from left and Depending on vehicle configuration.
right front fog lamp, expose electrical wiring
harness
10 Unscrew bolt (7) form left and right bracket
(8)
11 Guide bumper (1) out left and right bracket Installation: Install engine compartment
(8) paneling below bottom section of
soundproofing on bumper (1).
12 Press bumper (1) toward front and remove Installation: Screw in bolts (5, 7, 9) only
to stop because it may be necessary to
check and adjust the gap dimensions after
bumper (1) installation.
Model 207 AR60.00-P-0700-01EC
Gap dimension "C, E" *BE60.00-P-1001-01W
*129589032100
Page 2
Gap dimension "D, F" *BE60.00-P-1001-01U
*129589032100
13 Disassemble front bumper (1) Only when replacing bumper (1). AR88.20-P-2050EW
14 Install in the reverse order
15 Check adjustment of left front fog lamp and Model 207, 212 AP82.10-P-8260EW
right front fog lamp, adjust if necessary without code (615) Bi-xenon headlamp unit
with integrated curve illumination
without code (616) Bi-xenon headlamp unit
with integrated asymmetric curve illumination
without code (621) Intelligent Light System
(left-hand traffic system),
without code (622) Intelligent Light System
(right-hand traffic system)
Check values for gaps
Number Designation Model 207.3
BE60.00-P-1001-01W Gap Engine hood to fender Dim. "A" mm 4 ( 1)
dimension
Engine hood to headlamp Dim. "B" mm 4 ( 1)
Engine hood to bumper Dim. "C" mm 6 (+1/-2)
Engine hood to A-pillar Dim. "D" mm 4.5 (+2/-1)
Bumper to headlamp Dim. "E" mm 2.5 ( 1.5)
See picture
AR60.00-P-0700-01E
C
Check values for gaps
Number Designation Model 212.0/1 Model 212.2
BE60.00-P-1001-01U Gap Engine hood to fender Dim. "A" mm 4 ( 1) 4 ( 1)
dimension
Engine hood to headlamp Dim. "B" mm 4 ( 1) 4 ( 1)
Engine hood to radiator grille Dim. "C" mm - -
Engine hood to bumper Dim. "D" mm 4.5 ( 1.5) 4.5 ( 1.5)
Engine hood to A-pillar Dim. "E" mm 4.5 ( 1.5) 4.5 ( 1.5)
Bumper to headlamp Dim. "F" mm 3.5 ( 1.5) 3.5 ( 1.5)
See picture
AR60.00-P-0700-01E AR60.00-P-0700-01E
W W
110 589 03 59 00 129 589 03 21 00
Mounting wedge Feeler gauge